This specification covers the requirements for product performance and test methods of USB C TYPE Series Connectors. The product shall be of the design, construction, and physical dimensions specified in the applicable product drawing.
| Section | Item | Test Description | Test Methods | Requirement |
|---|---|---|---|---|
| 2.0 Rating | Current Rating (VBUS & GND pins) | 5.0A (1.25A/Pin) | ||
| 2.0 Rating | Current Rating (Other pins) | 0.25A/Pin | ||
| 3.0 Test Condition | Temperature Range | +15 to +35 | ||
| 3.0 Test Condition | Humidity Range | 90% Rh max. | ||
| 4.1 | Examination of product (Outward Appearance Structure) | Outward appearance shall be good without such injurious problem. Structure shall be meet the design and dimensional requirements of drawing. | EIA 364-18 | Confirmed by eyes and measuring instruments. |
| 4.2 Electrical Performance | Low Level Contact Resistance | Initial: 40m (Max) after 10000 insertion/extraction cycles: 50 m Maximum | EIA 364-23 (or MIL-STD-1344A, Method 3002.1, Test Condition B) | 40m (Max) at 20mv(max) open circuit at 100mA. Below 50 m after 10000 cycles. |
| 4.2 Electrical Performance | Insulation Resistance | EIA 364-21 (or MIL-STD-202F, Method 302, Test Condition B) | 100 M Minimum (DC 500 V applied for 1 minute) | |
| 4.2 Electrical Performance | Dielectric Withstanding Voltage | EIA 364-20 (or MIL-STD-202F, Method 301, Test Condition B) | No shortcircuiting and damage detected at AC 100 V R.M.S for 1 minute. | |
| 4.3 Mechanical Performance | Insertion Force | EIA 364-13 (Max rate: 12.5mm/min) | 5~20N | |
| 4.3 Mechanical Performance | Extraction Force | EIA 364-13 (Max rate: 12.5mm/min) | 8~20N | |
| 4.3 Mechanical Performance | Durability | No flashover or insulation breakdown. Extraction Force: Initial: 8~20N, After: 6~20N. Contact Resistance: Max.50m. Insertion/Extraction Force data recorded at specific cycles. | EIA 364-09 (10000 cycles at max 500 cycles/hour) | Meet visual requirements. Meet electrical and mechanical requirements after cycles. |
| 4.3 Mechanical Performance | Mechanical Shock | Subject mated connector to 50Gs half-sine shock pulses of 11msec duration. Three shocks in each direction applied along three mutually perpendicular planes (total 18 shocks). | EIA-364-27B | No discontinuities of 1 microsecond or longer duration. |
| 4.3 Mechanical Performance | Vibration | Subject mated connectors to 10~55~10Hz traversed in 1 minute at 1.52mm amplitude for 2 hours each of 3 mutually perpendicular planes. | EIA-364-28 | No discontinuities of 1 microsecond or longer duration. |
| 4.4 Environmental Performance | Thermal Shock | Ten cycles between 30 to +80. | EIA 364-32, Test Condition I (or MIL-202F, Method 107G Condition A) | Shall meet visual requirement, show no physical damage. Shall meet requirements of additional tests as specified in test sequence. |
| 4.4 Environmental Performance | Humidity | 96 Hours (Four complete cycles) | EIA 364-31, Test Condition A Method III (or MIL-202F, Method 103B Test Condition B) | Shall meet visual requirement, show no physical damage. Shall meet requirements of additional tests as specified in test sequence. |
| 4.4 Environmental Performance | Salt Spray | Duration: 48 hours. Environment in accordance with EIA-364-26B Method 101D, Condition B. (Temp: 35C2C, RH: 95~98%, Gas: 51% NaCl by weight) | EIA-364-26B Method 101D, Condition B | Shall meet visual requirement, show no physical damage. Shall meet requirements of additional tests as specified in test sequence. |
| 4.4 Environmental Performance | Temperature Life | Subject mated connectors to temperature life at 80 for 250 hours. | EIA 364-17 Test Condition 3 Method A | Shall meet visual requirement, show no physical damage. Shall meet requirements of additional tests as specified in test sequence. |
| 4.4 Environmental Performance | Solderability | After one hour steam aging. Solder dip technique. | EIA 364-52 | Surface of the portion to be soldered shall at least 95% covered with new solder coating. |
| 4.4 Environmental Performance | Resistance to Soldering Heat (WAVE SOLDERING) | Pre-heat: 80, 60 Seconds. Temperature: 260 5 . Immersion duration: 10 1 sec. | MIL-STD-202F, Method 210A, Test Condition B | No mechanical defect on housing or other parts. |
| 4.4 Environmental Performance | Resistance to Soldering Heat (REFLOW SOLDERING) | Pre-heat: 150(Min)~200(Max) , 60 ~180 Seconds. Temperature: 260 5 . Immersion duration: 10~40 sec. | EIAJ RCX-0101/102 | No mechanical defect on housing or other parts. |
