This document outlines the specifications for the HX IPEX 1.0-4P antenna seat manufactured by Shenzhen Hanxia Electronic Co., Ltd. It details the requirements for operating environment, storage, ratings, and various performance tests to ensure product quality and reliability.
All hazardous substances contained in this product should comply with the regulations specified by SGS.
The product performance must meet the specifications in section 3.4. Unless otherwise specified, all tests and measurements are to be performed under the following conditions: Temperature: 15~35, Humidity: 45% ~ 75%.
| Item | Requirements | Test Methods |
|---|---|---|
| Product Appearance | All components shall be properly assembled and free of burrs, warps, scratches, broken chips, and other abnormalities. Comply with method EIA 364-18B. Visual, functional, and dimensional inspection complies with applicable specification and document. | Visual Examination |
| Low Level Contact Resistance | Initial: 20m Max. Final: 70m Max. | |
| Insulation Resistance | Initial: 500 M Min. Final: 100 M Min. Comply with method EIA-364-21D. Insulation resistance is measured between adjacent contacts after applying 100V DC for 1 minute. | |
| Dielectric Withstanding Voltage | No evidence of breakdown or flash burn. No burn caused by short circuit. No insulation destruction. Current leakage: 0.50 mA Max. Comply with method EIA-364-20D, Test Method B. Apply 300V AC for 1 minute at sea level on tested plug and connectors. | |
| VSWR | Plug: 1.3 Max. (DC0.1~3GHz), 1.5 Max. (3~6GHz). Receptacle: 1.3 Max. (DC0.1~3GHz), 1.4 Max. (3~6GHz). Measure the VSWR as shown by the network analyzer. Frequency: 100M~6GHz. | |
| Un-mating force | Total un-mate force: Initial 5N Min. after 30 cycles 3N Min. Un-mate the receptacle connector (soldered to the test board) and plug at a speed of 253mm/minutes along the mating by the push-on/pull-off machine. | |
| Crimp strength | 5N MIN. Pull the cable as shown at a speed of 253mm/minutes by tensile strength machine. | |
| Durability | Contact resistance of inner contact: Initial 20m Max., after testing 40m Max. Contact resistance of ground contact: Initial 20m Max., after testing 40m Max. No abnormality. Mate and un-mate the receptacle connector (soldered to the test board) and plug 30 cycles at a speed of 253mm/minutes. Comply with method EIA 364-09C. | |
| Cable retention force | Appearance: Looseness between the parts, chipping, breakage or other abnormality shall not occur. Electrical discontinuity: No electrical discontinuity greater than 1 micro-sec. shall occur. Contact resistance of inner contact: Initial 20m Max., after testing 40m Max. Contact resistance of ground contact: Initial 20m Max., after testing 40m Max. Apply force on the cable as shown. During the testing, run 100mA DC to check electrical discontinuity. | |
| Vibration | Appearance: No abnormality. Electrical discontinuity: No electrical discontinuity greater than 1 micro-sec. shall occur. Contact resistance of inner contact: Initial 20m Max., after testing 40m Max. Contact resistance of ground contact: Initial 20m Max., after testing 40m Max. Apply the following vibration to the mating connector. Frequency: 10Hz-100Hz-10Hz/approx 20 minutes. Half amplitude, peak value of acceleration: 1.5mm or 59m/s(6G). Directions, cycle: 3 mutually perpendicular directions, 3 cycles for each direction. During the testing, run 100mA DC. Comply with method EIA 364-28E. | |
| Physical shock | Appearance: Looseness between the parts, chipping, breakage or other abnormality shall not occur. Electrical discontinuity: No electrical discontinuity greater than 1 micro-sec. shall occur. Contact resistance of inner contact: Initial 20m Max., after testing 40m Max. Contact resistance of ground contact: Initial 20m Max., after testing 40m Max. Apply the following vibration to the mating connector in accordance with MIL-STD-202, Method 213, Condition B. Peak value of acceleration: 735m/s(75G). Duration: 11msec. Wave Form: half sinusoidal. Directions, cycle: 6 mutually perpendicular, 3 cycles about each direction. During the testing, run 100mA DC to check electrical discontinuity. Comply with method EIA 364-27B. | |
| Humidity | Appearance: Looseness between the parts, chipping, breakage or other abnormality shall not occur. Contact resistance of inner contact: Initial 20m Max., after testing 40m Max. Contact resistance of ground contact: Initial 20m Max., after testing 40m Max. Insulation resistance: Initial 500M Min., after testing 100M Min. D.W. Voltage: No creeping discharge, flashover, nor insulator breakdown shall occur. Apply the following environment to the mating connector in accordance with Temperature: 313+/-2K(40+/-2C), Humidity: 90~95%RH, Duration: 96 hours. Comply with method EIA 364-31C, Method II, Condition A. | |
| Thermal shock | Appearance: Looseness between the parts, chipping, breakage or other abnormality shall not occur. Contact resistance of inner contact: Initial 20m Max., after testing 40m Max. Contact resistance of ground contact: Initial 20m Max., after testing 40m Max. Insulation resistance: Initial 500M Min., after testing 100M Min. D.W. Voltage: No creeping discharge, flashover, nor insulator breakdown shall occur. Apply the following environment to the mating connector. Temperature: 218K(-55C) for 30 min. <-> 358K(85C) for 30 min. Transition time: Max. 5 min. Number of cycles: 5 cycles. Comply with method EIA 364-32E. | |
| Temperature Life | Appearance: Looseness between the parts, chipping, breakage or other abnormality shall not occur. Contact resistance of inner contact: Initial 20m Max., after testing 40m Max. Contact resistance of ground contact: Initial 20m Max., after testing 40m Max. Insulation resistance: Initial 500M Min., after testing 100M Min. D.W. Voltage: No creeping discharge, flashover, nor insulator breakdown shall occur. Apply the following environment to the mating connector. Temperature: 313+/-2K(40+/-2C), Relative Humidity: 80+/-5%RH, Gas: H2S 3+/-1ppm, Duration: 96 hours. | |
| H2S Gas | Appearance: No abnormality adversely affecting the performance shall occur. Contact resistance of inner contact: Initial 20m Max., after testing 40m Max. Contact resistance of ground contact: Initial 20m Max., after testing 40m Max. Apply the following environment to the mating connector in accordance with MIL-STD-202, Method 101 Condition B. Temperature: 308+/-2K(35+/-2C), Humidity: 90~95%RH, Duration: 96 hours. | |
| Salt Spray | Appearance: No abnormality adversely affecting the performance shall occur. Contact resistance of inner contact: Initial 20m Max., after testing 40m Max. Contact resistance of ground contact: Initial 20m Max., after testing 40m Max. Apply the following environment to the mating connector in accordance with MIL-STD-202, Method 101, Condition B. Temperature: 308+/-2K(35+/-2C), Salt water density by weight: 5+/-1%, Duration: 48 hours. Comply with method EIA 364-26B, Method 101, Condition B. | |
| Solder ability | The number of reflow times is 2 within the profile. |
