Unmating: Insert the end of an extraction tool into a space between a plug and receptacle, and pull up the tool in the perpendicular to a mounting surface of a receptacle. Recommended the use of the extraction tool for unmating. Any attempt of unmating by pulling on the cable may result in damage to the mechanical / electrical performance.
Mating: Do not attempt to insert on an extreme angle.
Pull forces on the cable after connectors are mated: Do not apply any pull forces after the bending of the cable.
Precautions: Do not twist connectors excessively during mating / unmating.
Recommended reflow temperature profile: The temperature profile indicates the board surface temperature at the point of contacts with the connector leads. In individual applications the actual temperature may vary, depending on the solder paste type, volume / thickness and board size / thickness. Consult your solder paste and equipment manufacturer for the detailed recommendations.
Manual soldering: Soldering iron temperature: 350C, Soldering time: for 5 seconds max.
Recommended metal mask thickness: 0.1 mm 0.12 mm
Reflow cycles: 2 times
Operating environment: The connectors are not designed to operate in the following environments:
Storage conditions:
| Item | Specification | Conditions | Unit |
|---|---|---|---|
| Nominal characteristic impedance | 50 | ohms | |
| Frequency range | DC to 6 | GHz | |
| Operating temperature range | -40 to +90 | (90% RH max.) | C |
| Storage temperature range | -30 to +70 | (90% RH max.) | C |
| Contact resistance | Center contact: 25 max. | 10 mA max. | m ohms |
| Outer contact: 25 max. | 10 mA max. | m ohms | |
| Insulation resistance | 500 min. | 100V DC | M ohms |
| Withstanding voltage | No flashover or insulation breakdown | 200V AC / 1 minute | |
| V.S.W.R.(Note) | 1.3 max. | DC to 6GHz | |
| Durability | Center contact: 30 max. | 20 cycles | m ohms |
| Outer contact: 30 max. | 20 cycles | m ohms | |
| Vibration | No damage, cracks, or parts dislocation | Frequency: 10 to 100 Hz, single amplitude of 1.5 mm; Acceleration: 59 m/s, in each of 3 axis | |
| Shock | No damage, cracks, or parts dislocation | Acceleration of 735 m/s?, 11 ms continuous time; Waveform: sine half-wave, 3 cycles in each of the 3 axis | |
| Humidity | No damage, cracks, or parts dislocation | 96 hours at +40C, and humidity of 95% | |
| Temperature cycle | No damage, cracks, or parts dislocation | 5 cycles | |
| Salt spray test | No excessive corrosion | 5% salt water solution, 48 hours |
| Part | Material | Finish |
|---|---|---|
| Plugs - Right Angle | ||
| Shell | Phosphor bronze | Silver plated |
| Female center contact | Phosphor bronze | Gold plated |
| Insulator | PBT | Color: Black, UL94V-0 |
| Insulator (HF type) | PBT | Color: Gray, UL94HB |
| Receptacle | ||
| Shell | Phosphor bronze | Silver plated |
| Male center contact | Brass | Gold plated |
| Insulator | LCP | Color: Black, UL94V-0 |
| Part No. | HRS No. | RoHS |
|---|---|---|
| HRMP-U.FLJ(40) | 311-0300-2 | O |
| HRMJ-U.FLP(40) | 311-0301-5 | O |
| HRMJ-N.FLP-ST5 | 311-0423-2 | O |
| U.FL-R-1 | 331-0466-0 | O |
| U.FL-LP-IN | 331-0334-9 | O |
| U.FL-LP(V)-N-2 | 331-0493-2 | O |
